#----------------------------------------------------------------# 
# 
# Project: Configuration Example PPPoe CPE
# Element: SmartNode 4552 
# Firmware: 3.20
# Author: JW 
# Date: 2005-02-08
# Contact: EMEA: support@inalp.com
# 
#----------------------------------------------------------------# 

cli version 3.00
no dns-client enabled
dns-client cache 30
webserver port 80 language en
snmp community public ro

# The sntp configuration is optional
sntp-client

#change the ip-address of the time-server
sntp-client server primary <ip-address> port 123 version 4

sntp-client gmt-offset + 01:00:00

system hostname 4552


profile service-policy SP_VOICE_OUT

# Set rate-limit to the maximum uplink rate of your internet-connection
# voice-margin must be 1/3 of the rate-limit  
  rate-limit <speed> header-length 18 voice-margin <margin>

  source traffic-class local-voice
    priority

  source traffic-class local-default
    priority

  source traffic-class default

profile service-policy SP_VOICE_IN

# Set rate-limit to the maximum download rate of your internet-connection
# voice-margin must be 1/3 of the rate-limit  
  rate-limit <speed> header-length 18 voice-margin <margin>

  source traffic-class local-voice
    priority

  source traffic-class local-default
    priority

  source traffic-class default

profile ppp default

profile tone-set default

profile voip default
  codec 1 g729 rx-length 20 tx-length 20
  codec 2 g711alaw64k rx-length 20 tx-length 20
  codec 3 g711ulaw64k rx-length 20 tx-length 20
  dejitter-max-delay 100


profile pstn default

profile dhcp-server DHCP
# change the network ip-address and netmask to suit your network  
  network <ip-network> <netmask>

# define the ip-range
  include 1 <range start> <range end>

  lease 2 hours

# change your default router
  default-router 1 <ip-address>

profile authentication default
  method 1 local
  method 2 none


context ip router 

  interface IF_IP_WAN
    ipaddress unnumbered
    point-to-point
    icmp router-discovery
    tcp adjust-mss rx 1492
    tcp adjust-mss tx 1492
    use profile service-policy SP_VOICE_IN in
    use profile service-policy SP_VOICE_OUT out
    
  interface IF_IP_LAN
# change the IP adress and netmask of the SmartNode to suit your network
    ipaddress <ip-address> <netmask>

context ip router 
  dhcp-server use DHCP
  route 0.0.0.0 0.0.0.0 IF_IP_WAN 0
  

subscriber ppp SUB_PPPOE
  dial out
  authentication chap
  authentication pap

# change user-name an password to the settings given by your provider
  identification outbound <user-name> password <password>

  bind interface IF_IP_WAN router

context cs

  routing-table called-e164 RT_2_PSTN
    route default dest-interface IF_S0_00 MAP_CDPN_TO_PHONE
  
  mapping-table called-uri to called-e164 MAP_CDPN_TO_PHONE

# change your default phone number where SIP calls will routet to
    map default to <number>
  
  interface sip IF_SIP
    bind gateway GW_SIP
    route call dest-table RT_2_PSTN

  interface isdn IF_S0_00
    route call dest-interface IF_SIP

 context cs switch
  no shutdown      

gateway sip GW_SIP
# change the SIP-domain-name of your SIP-provider
  domain <domain-name>

# change the default SIP-server
  default-server <SIP-server> loose-router

# change the registrar server to be used for registration.
  registrar <registrar-server>

# change your user-id
  user <user-id>

# change the user-id and password
  authentication auto <user-id> <password> default

  call-transfer-version 5
  session-timer-version 8
  bind interface IF_IP_WAN router
  no shutdown

port ethernet 0 0
  encapsulation pppoe
  vlan 1
  no shutdown

  pppoe

    session SES_PPPOE_1
      bind subscriber SUB_PPPOE
      no shutdown

port ethernet 0 1		
  encapsulation ip 
  bind interface IF_IP_LAN router
  no shutdown 

port bri 0 0
  shutdown
  
port bri 0 1
  clock auto
  encapsulation q921

  q921

# Change the protocol to your requirements
# pp = point-to-point, pmp = point-to-multipoint
    protocol <pp | pmp>
  
    uni-side auto
    encapsulation q931

    q931
      protocol dss1

# Change the uni-side to your requirements
# user = pstn/PBX, net = telephone
      uni-side <user | net>
    
      encapsulation cc-isdn
      bind interface IF_S0_00 switch

port bri 0 1
  no shutdown