These QuikConnect™ Interface Plug-in Modules work interchangeably with Patton QuikConnect™ baseband modems, fiber modems, and CSU/DSUs





Patton QuikConnect™ Interface Modules work in with Patton QuikConnect baseband modems, fiber modems, and CSU/DSUs to provide an extremely wide array of access and transmission solutions. Each unit in the Model IM Series installs quickly, with no tools-and most require no configuration whatsoever. Just plug one in and go! Individual models are described below:

Model IM1/J - Data+Voice Module

  • Connects QuikConnect products to voice, fax and data hardware
  • 3 Ports allow simultaneous transmission of voice, fax and data over a single circuit
  • Port 1 (RJ-11) supports G3 fax or PSTN/compressed voice up to 14.4 kbps
  • Port 2 (RJ-11) supports PSTN/compressed voice
  • Port 3 (D-type) supports synchronous data from 64 to 704 kbps, (depending upon data rates of QuikConnect product)
  • Available in FXS (appears as telephone) or FXO (appears as CO) configuration
  • Data port is user-configurable for V.35, X.21, V.24/RS-232, RS-530 or RS-485 equipment

Model IM1/I - Ethernet Bridge Module

  • Supports Point-to-Point Protocol (PPP) RFC 1661 and Bridging Control Protocol, RFC 1638
  • Provides MAC level connection between two peered Ethernet LANs
  • Operates transparently to higher level protocols, such as TCP/IP, DECnet, NETBIOS and IPX
  • No configuration necessary
  • Automatically discovers, loads and deletes MAC addresses
  • 512K on-board RAM
  • Modular 10Base-T connection (RJ-45)
  • Two LED indicators: status and link integrity

Model IM1/F - 64k/G.703 Module

  • Connects QuikConnect products to Co-directional 64k/G.703 equipment
  • Provides 64k Co-directional interface compliant with the G.703 electrical specs
  • Offers a single TX/RX interface with standard RJ-45 connector as specified in TBR 14
  • Option to work in 2 timing modes: Clear Channel or octet timing
  • Complies with ITU/CCITT G.823 (Control of Jitter)
  • Point-to-point distance up to 4,000 feet (1219m) using 24AWG (.5mm) wire

Model IM1/D - Synchronous X.21 Module

  • Connects QuikConnect products to synchronous X.21 equipment
  • Data rates from 48 Kbps to 2.304 Mbps, depending on base unit selected
  • One DB-15F connector provided
  • No configuration necessary
  • Convenient no tools installation

Model IM1/C - Synchronous V.35 Module

  • Connects QuikConnect products to synchronous V.35 equipment
  • Data rates from 48 Kbps to 2.304 Mbps, depending on base unit selected
  • One M/34F connector provided
  • No configuration necessary
  • Convenient no tools installation

Model IM1/B - Synchronous RS-422/530 Module

  • Connects QuikConnect products to synchronous RS-422/530 equipment
  • Data rates from 48 Kbps to 2.304 Mbps, depending on base unit selected
  • One DB-25F connector provided
  • No configuration necessary
  • Convenient no tools installation
  • Connects QuikConnect

Model IM1/A - Synchronous V.24 (RS-232) Module

  • Connects QuikConnect products to synchronous V.24 (RS-232) equipment
  • Data rates from 48 to 512 Kbps, depending on base unit selected
  • One DB-25F connector provided
  • No configuration necessary
  • Convenient no tools installation

Models IM1/K & IM2RC/K - G.703/G.704 Quick Connect and Rear Card Modules

  • Support Point-to-Point Protocol (PPP) RFC 1661 and Bridging Control Protocol, RFC 1638
  • Quick Connect and Rear Card Modules for use with Patoon mDSL modems
  • nx64/G.704 Network Termination or Network Extension Applications
  • Support rates up to 2.048 (E1)
  • 2.048Mbps G.703 Clear Channel (Unframed) or nx64 G.704 (Framed) Operation
  • Selectable AMI or HDB3 Line Coding
  • Configuration va DIP switches and jumpers
  • Coax (BNC) connection for 75 Ohm
  • RJ-48C connection via twisted pair for 120 Ohm

Model IM2RC/IA - Ethernet Bridge Module

  • Support Point-to-Point Protocol (PPP) RFC 1661 and Bridging Control Protocol, RFC 1638
  • Installs in Patton's NetLink Rack Systems
  • Provides MAC level connection between two peered Ethernet LANs
  • RJ-45 line connection
  • Operates transparently to higher level protocols such as TCP/IP, DECnet, NETBIOS and IPX
  • No configuration necessary
  • Automatically discovers, loads and deletes MAC addresses
  • Modular 10Base-T connection (RJ-45)
  • Two LED indicators: status & link integrity

Model IM1/I4 - Ethernet Bridge with Integral 4-Port Hub QuikConnect Module

  • Support Point-to-Point Protocol (PPP) RFC 1661 and Bridging Control Protocol, RFC 1638
  • Standard interface module for use in QuikConnect platform
  • Integral 4-Port HUB
  • Industry standard RJ-45 10Base-T connections (four)
  • Transparent LAN bridging
  • 4096 MAC address table
  • 1 MB RAM; 128 KB FLASH
  • Throughput latency of 1 frame
  • Automatic LAN MAC address aging


Features
  • Compatible with Patton QuikConnect baseband modems, fiber modems, and CSU/DSUs
  • Provide a wide array of access and transmission solutions
  • Install quickly
  • Most modules require no configuration
  • Just plug one in and it's ready to use!
  • Made in the USA — This Patton equipment is designed by Patton engineers and built in our Gaithersburg, Maryland facility. Patton's American-made manufacturing process delivers high-quality networking solutions with reliability you can trust.